在三星注释10.1上安装TWRP -- adb 领域 和 samsung 领域 和 fastboot 领域 和 twrp 领域 和 samsung-galaxy-note-10.1 领域 android 相关 的问题

Install TWRP on Samsung Note 10.1


简体版||繁體版
1
vote

问题

中文

我追随来自cyanogenmods的本指南< / a>在Samsung Note 10.1上安装TWRP使用Android 5.1.1安装。我在开发人员选项中激活了 USB调试并将平板电脑连接到我的计算机,接受平板电脑中弹出的对话中的连接。然后我发出 adb 命令:

  $ adb reboot bootloader   

在计算机或平板电脑上没有错误消息,并且平板电脑重新启动。

然后我发出 flash 命令:
  $ fastboot flash twrp-3.0.2-0-lt03wifiue.img < waiting for device >   

,没有别的发生。平板电脑保持沉默,电脑中的命令行被卡住。我如何从这里开始?

更新i :这是我的计算机中的系统和软件:

  $ uname -a Linux ENG-PAVIL-PC2 4.4.0-87-generic #110-Ubuntu SMP Tue Jul 18 12:55:35 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux  $ apt policy adb adb:   Installed: (none)   Candidate: 1:6.0.1+r16-3   Version table:      1:6.0.1+r16-3 500         500 http://ch.archive.ubuntu.com/ubuntu xenial/universe amd64 Packages  $ apt policy fastboot fastboot:   Installed: (none)   Candidate: 1:6.0.1+r16-3   Version table:      1:6.0.1+r16-3 500         500 http://ch.archive.ubuntu.com/ubuntu xenial/universe amd64 Packages   

更新II :此平板电脑上的引导加载程序版本为:P600xxudqa1

更新III heimdall 在下面引用作为 fastboot 的替代方案,但它无法与三星注释10.1通信

  $ heimdall flash --no-reboot --RECOVERY twrp-3.0.2-0-lt03wifiue.img Heimdall v1.4.1  Copyright (c) 2010-2014 Benjamin Dobell, Glass Echidna http://www.glassechidna.com.au/  This software is provided free of charge. Copying and redistribution is encouraged.  If you appreciate this software and you would like to support future development please consider donating: http://www.glassechidna.com.au/donate/  Initialising connection... Detecting device... ERROR: Failed to detect compatible download-mode device.  $ adb devices List of devices attached  4300ee259691c037    device   

更新IV :仍然用 heimdall 尝试它,这是迄今为止提供任何一点希望的工具。出于某种原因,它有时无法识别下载模式 - 这是更新III中错误消息的原因。通过插入USB电缆并使用 ABCDeFghijklmnaBCDefghijklmn8 选项可以最终确保它获取设备:

  $ heimdall detect Device detected   
然后

然后 $ adb reboot bootloader 0 命令成功:

  $ adb reboot bootloader 1  

现在事情变得棘手。如果TWRP闪烁后通常重新启动平板电脑,库存引导程序(我相信)将自动替换它。在这种情况下,当平板电脑重新启动到恢复模式时,它将仅运行库存Android恢复程序。我花了一段时间来解决这个问题...

闪烁TWRP后,必须将平板电脑直接重新启动到恢复模式。问题是,它显示了引导屏幕中的错误:

无法正常启动。无效的内核长度!

twrp不加载,平板电脑刚刚关闭。这是我现在的目标。

english

I am following this guide from Cyanogenmods to install TWRP on a Samsung Note 10.1 with Android 5.1.1 installed. I have activated USB Debugging in Developer options and connected the tablet to my computer, accepting the connection in the dialogue that pops up in the tablet. I then issue the adb command:

$ adb reboot bootloader 

There is no error message, either on the computer or the tablet, and the tablet reboots.

I then issue the flash command:

$ fastboot flash twrp-3.0.2-0-lt03wifiue.img < waiting for device > 

And nothing else happens. The tablet remains silent and the command line in my computer is stuck. How do I move on from here?

Update I: This is the system and software in my computer:

$ uname -a Linux ENG-PAVIL-PC2 4.4.0-87-generic #110-Ubuntu SMP Tue Jul 18 12:55:35 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux  $ apt policy adb adb:   Installed: (none)   Candidate: 1:6.0.1+r16-3   Version table:      1:6.0.1+r16-3 500         500 http://ch.archive.ubuntu.com/ubuntu xenial/universe amd64 Packages  $ apt policy fastboot fastboot:   Installed: (none)   Candidate: 1:6.0.1+r16-3   Version table:      1:6.0.1+r16-3 500         500 http://ch.archive.ubuntu.com/ubuntu xenial/universe amd64 Packages 

Update II: The bootloader version on this tablet is: P600XXUDQA1

Update III: heimdall was referenced below as an alternative to fastboot, but it is not able to communicate with the Samsung Note 10.1:

$ heimdall flash --no-reboot --RECOVERY twrp-3.0.2-0-lt03wifiue.img Heimdall v1.4.1  Copyright (c) 2010-2014 Benjamin Dobell, Glass Echidna http://www.glassechidna.com.au/  This software is provided free of charge. Copying and redistribution is encouraged.  If you appreciate this software and you would like to support future development please consider donating: http://www.glassechidna.com.au/donate/  Initialising connection... Detecting device... ERROR: Failed to detect compatible download-mode device.  $ adb devices List of devices attached  4300ee259691c037    device 

Update IV: Still trying it out with heimdall, which so far is the only tool providing any bit of hope. For some reason it sometimes fails to identify Download mode - that is the reason for the error messages in Update III. By plugging in/out the USB cable and using the detect option one can eventually make sure it acquired the device:

$ heimdall detect Device detected 

Then the flash command succeeds:

$ heimdall flash --no-reboot --RECOVERY twrp-3.0.2-0-lt03wifiue.img Heimdall v1.4.1  Copyright (c) 2010-2014 Benjamin Dobell, Glass Echidna http://www.glassechidna.com.au/  This software is provided free of charge. Copying and redistribution is encouraged.  If you appreciate this software and you would like to support future development please consider donating: http://www.glassechidna.com.au/donate/  Initialising connection... Detecting device... Claiming interface... Setting up interface...  Initialising protocol... Protocol initialisation successful.  Beginning session...  Some devices may take up to 2 minutes to respond. Please be patient!  Session begun.  Downloading device's PIT file... PIT file download successful.  Uploading RECOVERY 100% RECOVERY upload successful  Ending session... Releasing device interface... 

Now things get tricky. If the tablet is rebooted normally after TWRP is flashed, the stock bootloader (I believe) will replace it automatically. In this case when the tablet is rebooted into recovery mode it will just run the stock Android recovery programme. It took me a while to figure this one out...

After flashing TWRP, the tablet must be rebooted directly into recovery mode. The problem is, it shows an error in the booting screen:

Could not do normal boot. Invalid KERNEL LENGTH!

TWRP does not load and the tablet just shuts down. That is how far I am right now.

              
         
         

回答列表

4
 
vote
vote
最佳答案
 

注释10.1(2014)其引导加载程序默认解锁,就像大多数如果不是所有设备都是Annouced Pre-Lollipop一样。

在Windows下,实际安装如 Twrp设备页面:

您需要在PC上下载并安装ODIN。安装ODIN后,从上面的下载链接下载设备的适当.tar文件。关闭您的设备。使用正确的键组合打开您的设备进入下载模式并通过USB电缆将设备连接到计算机。使用PDA选项卡或按钮浏览到并选择您下载并刷新设备的Tar文件。

在Linux下,Heimdall是必需的,步骤有点不同:下载 .img 文件,进入下载模式,(可选地)与 heimdall detect ,然后执行 heimdall flash --no-reboot --RECOVERY /path/to/recovery.img 将其闪烁到设备。

请注意,此设备的不同,非常不同的变体。 WiFi版本(P600)和LTE版本(P605)基于不同的SOC,因此使用不同的恢复和ROM,而Verizon变量(P605V)具有锁定(和非可解锁)引导加载程序,这意味着您无法刷新任何内容在它。

 

Note 10.1 (2014) has its bootloader unlocked by default, just like most if not all devices annouced pre-Lollipop.

Under Windows, the actual installation is as simple as described in the TWRP device page:

You will need to download and install Odin on your PC. Once you have Odin installed, download the proper .tar file for your device from the download link above. Power off your device. Turn on your device using the proper key combo to get into download mode and attach the device to your computer via a USB cable. Use the PDA tab or button to browse to and select the tar file that you downloaded and flash the device.

Under Linux, Heimdall is required instead, and steps are somewhat different: download the .img file, get into download mode, (optionally) verify connection with heimdall detect, then execute heimdall flash --no-reboot --RECOVERY /path/to/recovery.img to flash it to the device.

Do note that there are multiple, very different variants of this device. The WiFi version (P600) and LTE version (P605) are based on different SoCs and therefore use different recoveries and ROMs, while the Verizon variant (P605V) has a locked (and non-unlockable) bootloader which means you can't flash anything on it.

 
 
         
         

相关问题

1  Galaxy笔记不使用Apple Router  ( Galaxy note not working with apple router ) 
我有一个新的Galaxy Note 10.1(2014)平板电脑,我绝对爱。我一直在使用它来参加讲义笔记,事情很棒。 平板电脑的wifi与每个网络都能良好......除了我家里的一个网络。我有一个苹果机场表达,我用作我大学的100Mbps以太网线的集线器;我联系了三星支持只能获得标准"与您的ISP谈论DNS设置" 罐...

2  TWRP:未能挂载'/ preload'(无效的参数)  ( Twrp failed to mount preload invalid argument ) 
使用twrp,几乎每个操作我得到 无法挂载'/ preload'(无效参数) 我的设备目前无法启动,这可能会与它有关, /preload 当前在 /etc/fstab 中,我可以在这里看到这里的条目 /dev/block/mmcblk0p16 /preload ext4 rw 0 0 当我尝试安装它时,...

0  Galaxy Note 10.1,不识别手指触摸  ( Galaxy note 10 1 does not recognize finger touch ) 
我有一个Galaxy Note 10.1,它突然停止(开启时)手指触摸检测,但正常使用S笔。我试过工厂重置,但它仍然没有检测到手指触摸......我试图找到有关手指触摸的任何设置,但我不能。有没有办法解决这个问题? ...

0  GT-N8000有特定的硬件差异吗?  ( Are there region specific hardware differences to gt n8000 ) 
是否有区域特定的硬件差异与GT-N8000,或者是一个GT-N8000相同的设备,无论您在哪里居住吗? 我认为三星的型号名称(GT-I9300,SM-G900F,GT-N8000)是一种安全的方法来识别内部的硬件。是具有相同型号名称的设备,在所有方面都是相同的,除了区域特定/单元格提供者特定的固件? ...

0  SM-P600,LTE,WiFi或3G?  ( Sm p600 lte wifi or 3g ) 
我在每次在SM-P600上启动ROM时都有问题,我会停止跳动。我想知道如何验证我有哪个版本。 LineaGeos有一个版本, n1awifi lt03lte ...

7  如何在三星Galaxy注释10.1上调整S Pen压力敏感性?  ( How to adjust s pen pressure sensitivity on a samsung galaxy note 10 1 ) 
对我来说有点背景:我是一名专业的漫画家,一直在数量的数字约20年。我有许多Wacom设备&amp;目前享受Cintiq 21ux(旧模型)。我也有华硕EP121 Slate。我想我很好地了解Wacoms,通常不会恐慌电脑的东西。 三星注意10.1 S笔使用Wacom的收集的技术。在华硕EP 121中的相同类型的硬件。...

1  如何找出Note 10 Lite是假的吗?  ( How to find out if note 10 lite is fake ) 
如果我打算购买使用的说明10 lite,检查的方法是原创的,而不是假的? ...

1  剪切和粘贴不在三星注意10.1上工作  ( Cut and paste not working on samsung note 10 1 ) 
我最近买了三星注10.1平板电脑。它具有Android 4.0.4(型号 GT-N8000 / N8000XXLGA )。一切都很好,但我无法理解为什么剪切和粘贴不起作用。这是一个已知的问题吗?我可以更新到更新的版本还是什么......?我尝试复制/削减的每个应用程序。粘贴刚刚崩溃。 这很烦人,我一直在尝试在线找到大...

0  哪个版本的vlc是exynos平板电脑的权利?  ( Which version of vlc is right for an exynos tablet ) 
vlc有列出的ARM, Android(ARMV7-A) Android(ARMV8-A) 我宁愿不使用playstore安装。当下载时,这两个版本都在文件管理器中单击时"无法打开文件" 。 对于比较,我也下载 f-droid 单击它为我打开提示使用选项 INSTALL 和 CANCEL 。我正在使用三星...

1  lt03wifiue构建与n1awifi相同吗?  ( Is the lt03wifiue build the same as n1awifi ) 
我有一个sm-p600,当我下载twrp它显示 lt03wifiue for build name。当我下载lineageos时,它显示 n1awifi 用于构建名称。这两个是相同的构建吗? ...




© 2022 it.wenda123.org All Rights Reserved. 问答之家 版权所有